Exploring Plumbing Fundamentals for Installing a Bathtub
Exploring Plumbing Fundamentals for Installing a Bathtub
Blog Article
We have noticed this article on Tools You Need to Install a New Bathtub listed below on the net and reckoned it made good sense to discuss it with you here.
Setting up a tub isn't specifically rocket science, however it does require solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately hard task. If the old bathtub is readily easily accessible, the task can move immediately; if you have to open up a wall to remove the old tub and place the new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require an assistant to leave the old tub and embeded in the new one. See to it you have qualified yourself for the work as well as fit attempting it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to take into consideration utilizing one before you start. Chances are you might require an expert plumber to make tube links.
This post will certainly help you mount a brand-new tub in your shower room if you have currently gotten a brand-new bathtub as well as do not require to alter the arrangement of your previous water pipes.
Your devices as well as product list must consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly bothersome because of the limited gain access to that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have actually been eliminated, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Before going on to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin making certain that the washers are in place between the faucet and the sink. Secure the tap in place with the supplier supplied backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet adapters. The former kind ought to be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using the two wooden boards under its feet, place the bathtub in the called for placement. The wood boards are valuable in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reads level.
To mount faucets, fit the bottom of the furthest flexible faucet port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water supply and inspect all joints and new pipework for leaks and also tighten them if required. Fill the bath tub as well as also check the overflow outlet and the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the producer's instruction manual. Tiling and also sealing around the tub needs to wait till the tub has been used at the very least when as this will settle it right into its final position.
Getting ready for the Installment
To start with, the supporting frame supplied with the bath ought to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to stop pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of the two taps using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to fracture an inflexible seal, triggering the water to penetrate the wall between the bathroom and the tiling, causing issues with moisture and also possible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealer can break rather early if you do not consider this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the market. It is suggested to fit the tiles utilizing water-resistant or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading up on Installing A Bathtub? Write a review below. We'd be delighted to listen to your insights about this entry. In hopes that you visit us again in the future. Make sure you take the opportunity to promote this entry if you appreciated it. Thank you for taking the time to read it.
Quality service? Ring us. Report this page